Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Platinum Sputtering Target, Pt

Material: Platinum Sputtering Target
Formula: Pt
Catalog No.: TFM-SPT-0485

Elemental Pt source for sputtered thin films. Specify purity and impurity limits, target geometry, backing interface, and film acceptance requirements in the RFQ. Grade, dimensions, assembly, documentation and availability are confirmed in the quotation.

CoA_PtTRG

What is a platinum sputtering target?

A platinum (Pt) sputtering target is an elemental-metal source for depositing Pt-containing thin films by physical vapor deposition. The ordered target grade and assembly must be matched to the film's contamination limits and the cathode drawing; target composition alone does not establish film acceptance.

Using evaporation instead? See the platinum evaporation material page for the corresponding product form.

Explore related materials in the Sputtering Targets catalog.


Platinum

Material and Deposition Characteristics

Because the target is electrically conductive, DC magnetron sputtering is often applicable, although pulsed-DC or other power modes may also be used depending on the deposition system and film target. For high-specification films, target grain structure, residual stress, and surface preparation can influence erosion uniformity and the morphology of the deposited layer. When higher power loading or system-specific mounting is involved, a bonded target assembly may also be considered.

How to specify platinum sputtering target for an RFQ

The following fields define the order and the tests needed to qualify this target; final availability and acceptance criteria belong in the approved quotation or drawing.

DecisionInformation to provide or verify
Material identityState the Pt purity basis and the specific trace elements that matter to the film specification; request lot evidence where required.
Target and cathode fitProvide target diameter or outline, thickness, cathode model, mounting interface, and whether a backing plate or bonded assembly is required.
Film acceptanceDefine film composition, thickness, adhesion or electrical measurements required by the application and the inspection documents needed for acceptance.

Send the specification and drawing for review. The selected source or target and the deposited film require separate acceptance evidence.

Research applications and film checks

  • Platinum electrode films on SiO2 have been investigated using both electron-cyclotron-resonance and DC-magnetron sputtering. The comparison reported differences in flatness, adhesion and resistivity, illustrating that the process matters as well as the Pt source (research example).
  • For an electrode or contact layer, specify the substrate, adhesion-layer strategy, post-treatment and required electrical/adhesion tests. Qualify the final Pt film and interfaces in the intended stack.
  • Confirm target purity, dimensions and cathode fit in the RFQ; do not treat published film behavior as a guaranteed outcome of the supplied target.

Target Configuration and Ordering Considerations

For quotation and manufacturability review, provide target size, thickness, purity or alloy composition, quantity, and the sputtering gun or cathode model if known. If a bonded assembly is required, include backing-plate material, bonding preference, and any dimensional tolerances, surface-finish needs, or inspection-document requirements. TFM can also review customer drawings or old-target samples for replacement builds.

Typical specification reference: Download the Platinum Sputtering Target Typical Specification Sheet (PDF). This planning reference is not a batch CoA; confirm final specifications and batch documentation in the quotation.

Frequently Asked Questions

Can Platinum sputtering targets be used with DC magnetron sputtering?

Yes. Conductive metallic targets are commonly processed with DC magnetron sputtering, although pulsed-DC or other modes may also be used depending on the equipment and film objective.

What purity grade should I choose for a Platinum target?

The required purity should be selected from the contamination limits and performance needs of the deposited film. Higher purity can reduce unwanted impurities, but the optimum grade should match the application rather than default to the highest available level.

Why do density and microstructure matter for Platinum targets?

Target density, grain structure, and residual stress can influence erosion behavior, process stability, and the morphology of the deposited film. These factors become more important as film-quality requirements become tighter.

Can a Platinum target be bonded to a copper backing plate?

Yes. A bonded assembly may be used when the cathode design requires a backing plate or when improved support and heat transfer are desirable. The bonding method should be matched to target thickness and operating conditions. Review the bonded vs unbonded sputtering target selection guide when comparing assembly options.

What are common applications of sputtered Platinum films?

Typical uses include conductive layers, metallization, reflective or protective coatings, and composition-specific PVD research. The exact application depends on the properties of the element and the final film stack.

What information should I send TFM for a custom Platinum target?

Please provide target dimensions, thickness, purity, quantity, target style, backing-plate requirement, cathode model if known, and any tolerance, surface-finish, inspection, or documentation requirements through the TFM contact and RFQ path.

Order Now

Ø1" × 3.18 mm, Platinum (Pt), 4N, Ø2" × 1 mm, Platinum (Pt), 4N, Ø2" × 1.60 mm, Platinum (Pt), 4N, Ø2" × 2.5 mm, Platinum (Pt), 4N, Ø2" × 3.18 mm, Platinum (Pt), 4N, Ø2" × 3.18 mm + 3.18 mm Cu Backing Plate, Platinum (Pt), 4N, Ø2" × 5 mm, Platinum (Pt), 4N, Ø2.52" × 0.5 mm, Platinum (Pt), 4N, Ø3" × 1.60 mm, Platinum (Pt), 4N

Reviews

There are no reviews yet.

Be the first to review “Platinum Sputtering Target, Pt”

Your email address will not be published. Required fields are marked *

Related Products

FAQ

It’s the source material (in solid form) used in sputter deposition to eject atoms or molecules that then form a thin film on a substrate.

Targets can be pure metals (e.g., gold, copper, aluminum), ceramics (e.g., Al₂O₃, SiO₂, TiO₂), alloys, or composites—chosen based on the film’s desired properties.

 

Manufacturing routes depend on the material and target specification. Metal targets may be cast and machined, while some ceramic targets are consolidated by sintering. Ask for the product-specific route and inspection criteria when these affect qualification.

 

In a vacuum chamber, a plasma (typically argon) bombards the target, ejecting atoms that travel and condense on a substrate, forming a thin film.

 

Key factors include the target’s purity, density, grain structure, and the sputtering yield (i.e. how many atoms are ejected per incident ion), as well as operating conditions like power density and gas pressure.

 

Operators monitor target erosion (often by measuring the depth of the eroded “race track”) or track total energy delivered (kilowatt-hours) until it reaches a threshold that can compromise film quality.

 

Bonding may be selected for brittle targets, thinner precious-metal targets, or a cathode that needs a specific backing and cooling arrangement. It is not a universal requirement. Provide target and backing dimensions, the cathode model, and operating conditions for assembly review.

 

DC is commonly used with conductive targets. RF is often used for poorly conducting or insulating targets to mitigate surface charging; other power modes may be suitable depending on the target, cathode, and process. Confirm the mode against the equipment and material.

 

In reactive sputtering, a reactive gas (e.g., oxygen or nitrogen) is introduced to form compound films on the substrate, but it may also “poison” the target surface if not carefully controlled.

 

Customer-supplied powder acceptance is not assumed. Provide material identity, lot traceability, composition and impurity analysis, quantity, and handling constraints in the RFQ. TFM must confirm feasibility and acceptance criteria before any material is sent.

 

Targets should be stored in clean, dry conditions (often in original packaging or re-wrapped in protective materials) and handled with gloves to avoid contamination, ensuring optimal performance during deposition.

Deposition rate depends on factors such as target material and composition, power density, working gas pressure, substrate distance, and the configuration of the sputtering system (e.g., magnetron design).

 
Shopping Cart
Scroll to Top