Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Indium Zinc Oxide Sputtering Target, IZO

Material: Indium Zinc Oxide
Composition: In2O3/ZnO
Catalog No.: TFM-SPT-0273

Indium Zinc Oxide (IZO) sputtering target is a compound-oxide source material for PVD process development. For quotation, specify the required In2O3:ZnO composition, purity basis, geometry, dimensions, backing or bonding, quantity, and inspection or document requirements.

COA_IZO_TRGPDF

What is an indium zinc oxide sputtering target?

An indium zinc oxide (IZO) sputtering target is an indium-oxide/zinc-oxide ceramic source used to deposit transparent conductive or other functional oxide films by sputtering. The RFQ should define the In2O3/ZnO ratio and its basis, purity basis, target geometry, density or microstructure acceptance method, cathode and backing requirements, and film measurements. Source composition and target properties affect process development, but deposited-film performance must be verified on the intended system.

Use the Sputtering Targets catalog when the material family or target format is still being selected.


Material and Deposition Characteristics

RF magnetron sputtering is commonly considered for insulating or semiconducting oxide targets, while sufficiently conductive formulations may allow alternative power modes in some systems. Target density and microstructural uniformity matter because pores, cracks, and local inhomogeneities can contribute to unstable plasma, particles, or target damage. For brittle ceramics, bonded assemblies and gradual power ramping are often worth evaluating.

IZO sputtering target selection data

Selection fieldWhat to specifyWhy it matters
Material identityIn2O3/ZnO ratio, composition basis, and purity basisDefines the requested IZO chemistry without assuming one universal ratio
Target geometryShape, finished dimensions, tolerances, quantity, and drawing revisionConnects the material requirement to the cathode interface
Density and microstructureRequired value or acceptance method, sampling, and document expectationAvoids treating an unspecified catalog number as the order requirement
Backing and bondingCathode model, backing material and dimensions, interface request, cooling, and operating contextAllows mechanical and thermal-path requirements to be reviewed together
Process and film checksPower mode plus composition, thickness, optical, electrical, structural, or defect measurementsThe film must be qualified under the intended process window
Inspection and documentsList dimensional, composition, density, visual, packaging, or lot-document evidence requiredKeeps acceptance evidence distinct from catalog assumptions

Typical Thin-Film Applications

  • Transparent conductive and other indium-zinc-oxide film research
  • Display, optical, electronic, sensor, photovoltaic, or multilayer studies where the approved design specifies IZO
  • Projects with defined film composition, thickness, optical, electrical, structural, or defect measurements

Application fit depends on the complete layer design and qualified process. Review the broader thin-film application categories before finalizing the target RFQ.

Target Configuration and Ordering Considerations

For an IZO target quotation, provide the In2O3/ZnO ratio and composition basis, purity basis, finished dimensions and drawing revision, quantity, cathode model, backing and interface requirements, cooling and operating context, plus any density, tolerance, inspection, packaging, or lot-document requirements. Send the available drawing and acceptance criteria to TFM for review; unlisted ratios, dimensions, bonding, packaging, and performance requirements remain subject to quotation and approved specification.

Frequently Asked Questions

Is Indium Zinc Oxide better suited to RF or DC sputtering?

RF magnetron sputtering is commonly considered for insulating or semiconducting oxide targets. If a specific formulation is sufficiently conductive, other modes may also be possible, but the equipment and target properties should be confirmed.

Why is density important for an Indium Zinc Oxide target?

Density and microstructural uniformity affect erosion stability, thermal behavior, and particle risk. Pores, cracks, or local density variations can contribute to unstable sputtering and target damage.

Should an Indium Zinc Oxide target be bonded to a backing plate?

Bonding is often useful for brittle oxide targets because it can improve mechanical support and heat transfer. The backing material and bonding method should be chosen according to target size, thickness, and operating conditions.

Will the deposited film always have the same composition as IZO?

Not always. Film composition can be affected by preferential sputtering, reactive gas, substrate temperature, re-sputtering, and chamber conditions. Composition-sensitive films should be verified after deposition.

How should power be ramped on a brittle Indium Zinc Oxide target?

A conservative power ramp and stable cooling are generally advisable. The exact operating procedure should follow the target size, bonding condition, cathode design, and supplier recommendations rather than a universal wattage.

What information should I provide when ordering Indium Zinc Oxide?

Provide formula or composition, purity, dimensions, quantity, backing and bonding requirements, cathode model or drawing, and any density, tolerance, or inspection requirements.

Prepare your RFQ: Download the fillable Indium Zinc Oxide Sputtering Target, IZO RFQ Worksheet (PDF). Enter the required composition or grade, dimensions, backing or bonding request, quantity, documents, and acceptance criteria for quotation review.

Order Now

Ø1/16" × 1/16", IZO (In₂O₃/ZnO = 90/10 at%), Bonded, Ø2" × 3.18 mm, IZO (In₂O₃/ZnO = 90/10 wt%), 4N, Ø2" × 4 mm, IZO (In₂O₃/ZnO = 85/15 wt%), 4N, 2 mm Cu B/P (<6.35 mm Total), Ø3" × 3.18 mm, IZO (In₂O₃/ZnO = 90/10 wt%), 4N, Ø3" × 3.18 mm, IZO, 4N, Ø3" × 6.35 mm, IZO (In₂O₃/ZnO = 90/10 wt%), 4N, 3 mm Cu B/P, Ø4" × 3.18 mm, IZO (In₂O₃/ZnO = 90/10 wt%), 4N, Ø6" × 6 mm, IZO (In₂O₃/ZnO = 90/10 wt%), 4N, Unbonded, Ø150 mm × 6 mm, IZO (In₂O₃/ZnO = 90/10 wt%), 3N5, Ø150 mm × 6 mm, IZO (In₂O₃/ZnO = 65/35 wt%), 3N5, Ø3" × 3.18 mm, Indium Zinc Oxide (IZO), 4N, Bonded to 3.18 mm Cu B/P, Ø50.8 × 3.18 mm (2" × 1/8"), IZO TRG, In2O3-ZnO 90/10 wt%, 4N, Ø50.8 × 6.35 mm (2" × 1/4"), IZO TRG, In2O3-ZnO 90/10 wt%, 4N

Reviews

There are no reviews yet.

Be the first to review “Indium Zinc Oxide Sputtering Target, IZO”

Your email address will not be published. Required fields are marked *

FAQ

It’s the source material (in solid form) used in sputter deposition to eject atoms or molecules that then form a thin film on a substrate.

Targets can be pure metals (e.g., gold, copper, aluminum), ceramics (e.g., Al₂O₃, SiO₂, TiO₂), alloys, or composites—chosen based on the film’s desired properties.

 

Manufacturing routes depend on the material and target specification. Metal targets may be cast and machined, while some ceramic targets are consolidated by sintering. Ask for the product-specific route and inspection criteria when these affect qualification.

 

In a vacuum chamber, a plasma (typically argon) bombards the target, ejecting atoms that travel and condense on a substrate, forming a thin film.

 

Key factors include the target’s purity, density, grain structure, and the sputtering yield (i.e. how many atoms are ejected per incident ion), as well as operating conditions like power density and gas pressure.

 

Operators monitor target erosion (often by measuring the depth of the eroded “race track”) or track total energy delivered (kilowatt-hours) until it reaches a threshold that can compromise film quality.

 

Bonding may be selected for brittle targets, thinner precious-metal targets, or a cathode that needs a specific backing and cooling arrangement. It is not a universal requirement. Provide target and backing dimensions, the cathode model, and operating conditions for assembly review.

 

DC is commonly used with conductive targets. RF is often used for poorly conducting or insulating targets to mitigate surface charging; other power modes may be suitable depending on the target, cathode, and process. Confirm the mode against the equipment and material.

 

In reactive sputtering, a reactive gas (e.g., oxygen or nitrogen) is introduced to form compound films on the substrate, but it may also “poison” the target surface if not carefully controlled.

 

Customer-supplied powder acceptance is not assumed. Provide material identity, lot traceability, composition and impurity analysis, quantity, and handling constraints in the RFQ. TFM must confirm feasibility and acceptance criteria before any material is sent.

 

Targets should be stored in clean, dry conditions (often in original packaging or re-wrapped in protective materials) and handled with gloves to avoid contamination, ensuring optimal performance during deposition.

Deposition rate depends on factors such as target material and composition, power density, working gas pressure, substrate distance, and the configuration of the sputtering system (e.g., magnetron design).

 
Shopping Cart
Scroll to Top