Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Silver Sputtering Target, Ag

Material: Silver Sputtering Target
Formula: Ag
Catalog No.: TFM-SPT-0538
CAS: 7440-22-4

Elemental Ag source for sputter deposition. Specify purity and impurity limits, geometry, cathode fit and backing requirements. Final grade, dimensions and documents are agreed in the quotation.

What is a silver sputtering target?

A silver sputtering target is a solid elemental Ag source for sputter deposition, with geometry matched to the sputtering cathode. Silver evaporation material is a separate source form selected for an evaporation system. Confirm the deposition route before specifying geometry. Compare the Silver (Ag) Evaporation Material when defining the source form.

Explore related material families and formats in the Sputtering Targets catalog.


Silver

Material and Deposition Characteristics

Because the target is electrically conductive, DC magnetron sputtering is often applicable, although pulsed-DC or other power modes may also be used depending on the deposition system and film target. For high-specification films, target grain structure, residual stress, and surface preparation can influence erosion uniformity and the morphology of the deposited layer. When higher power loading or system-specific mounting is involved, a bonded target assembly may also be considered.

Silver Reference and RFQ

Material identityElemental silver (Ag); atomic number 47; CAS 7440-22-4.
Elemental melting point961.78 °C (RSC reference).
Elemental density10.5 g/cm³ at room temperature (RSC reference), not a target-density acceptance limit.
Purity and impuritiesSpecify the required Ag grade and individual impurity limits from the film contamination requirements; confirm the analysis method and acceptance basis.
Geometry and assemblyProvide target diameter or drawing, thickness, tolerances, cathode model and backing interface. Bond method and finished assembly dimensions require order-specific agreement.
DocumentationSpecify sample/lot traceability, analysis method, inspection records and the agreed acceptance limits.

Element reference: Royal Society of Chemistry – Silver. Product grade, dimensions, assembly and availability are confirmed in the quotation.

Film Requirements to Define Before Ordering

For electrical or optical layer development, specify the substrate, layer stack, film thickness and required continuity, adhesion or optical measurements. Bulk silver reference properties do not establish the performance of a deposited Ag film; qualify the film under the intended processing and exposure conditions.

Target Configuration and Ordering Considerations

For quotation and manufacturability review, provide target size, thickness, purity or alloy composition, quantity, and the sputtering gun or cathode model if known. If a bonded assembly is required, include backing-plate material, bonding preference, and any dimensional tolerances, surface-finish needs, or inspection-document requirements. TFM can also review customer drawings or old-target samples for replacement builds.

Typical specification reference: Download the Silver Sputtering Target Typical Specification Sheet (PDF). This planning reference is not a batch CoA; confirm final specifications and batch documentation in the quotation.

Frequently Asked Questions

Can Silver sputtering targets be used with DC magnetron sputtering?

Yes. Conductive metallic targets are commonly processed with DC magnetron sputtering, although pulsed-DC or other modes may also be used depending on the equipment and film objective.

What purity grade should I choose for a Silver target?

The required purity should be selected from the contamination limits and performance needs of the deposited film. Higher purity can reduce unwanted impurities, but the optimum grade should match the application rather than default to the highest available level.

Why do density and microstructure matter for Silver targets?

Target density, grain structure, and residual stress can influence erosion behavior, process stability, and the morphology of the deposited film. These factors become more important as film-quality requirements become tighter.

Can a Silver target be bonded to a copper backing plate?

A copper-backed assembly is an option to review against the cathode and target requirements. Provide the target thickness, backing dimensions, interface drawing and operating conditions; confirm bond method and compatibility in the quotation. The bonded versus unbonded target guide explains the assembly information to compare.

What are common applications of sputtered Silver films?

Typical uses include conductive layers, metallization, reflective or protective coatings, and composition-specific PVD research. The exact application depends on the properties of the element and the final film stack.

What information should I send TFM for a custom Silver target?

Please provide target dimensions, thickness, purity, quantity, target style, backing-plate requirement, cathode model if known, and any tolerance, surface-finish, inspection, or documentation requirements through the TFM contact and RFQ path.

Order Now

Ø1" × 3.18 mm, Silver (Ag), 4N, Ø1" × 6.35 mm, Silver (Ag), 4N, Ø2" × 3.18 mm, Silver (Ag), 4N, Ø2" × 6.35 mm, Silver (Ag), 4N, Ø2" × 6.35 mm, Silver (Ag), 4N, U.S. Gun, Ø2" × 6.35 mm, Silver (Ag), 4N, TORUS Mag Keeper, Ø3" × 3.18 mm, Silver (Ag), 4N, Ø3" × 6.35 mm, Silver (Ag), 4N, Ø3" × 6.35 mm, Silver (Ag), 4N, TORUS Mag Keeper

Reviews

There are no reviews yet.

Be the first to review “Silver Sputtering Target, Ag”

Your email address will not be published. Required fields are marked *

Related Products

FAQ

It’s the source material (in solid form) used in sputter deposition to eject atoms or molecules that then form a thin film on a substrate.

Targets can be pure metals (e.g., gold, copper, aluminum), ceramics (e.g., Al₂O₃, SiO₂, TiO₂), alloys, or composites—chosen based on the film’s desired properties.

 

Manufacturing routes depend on the material and target specification. Metal targets may be cast and machined, while some ceramic targets are consolidated by sintering. Ask for the product-specific route and inspection criteria when these affect qualification.

 

In a vacuum chamber, a plasma (typically argon) bombards the target, ejecting atoms that travel and condense on a substrate, forming a thin film.

 

Key factors include the target’s purity, density, grain structure, and the sputtering yield (i.e. how many atoms are ejected per incident ion), as well as operating conditions like power density and gas pressure.

 

Operators monitor target erosion (often by measuring the depth of the eroded “race track”) or track total energy delivered (kilowatt-hours) until it reaches a threshold that can compromise film quality.

 

Bonding may be selected for brittle targets, thinner precious-metal targets, or a cathode that needs a specific backing and cooling arrangement. It is not a universal requirement. Provide target and backing dimensions, the cathode model, and operating conditions for assembly review.

 

DC is commonly used with conductive targets. RF is often used for poorly conducting or insulating targets to mitigate surface charging; other power modes may be suitable depending on the target, cathode, and process. Confirm the mode against the equipment and material.

 

In reactive sputtering, a reactive gas (e.g., oxygen or nitrogen) is introduced to form compound films on the substrate, but it may also “poison” the target surface if not carefully controlled.

 

Customer-supplied powder acceptance is not assumed. Provide material identity, lot traceability, composition and impurity analysis, quantity, and handling constraints in the RFQ. TFM must confirm feasibility and acceptance criteria before any material is sent.

 

Targets should be stored in clean, dry conditions (often in original packaging or re-wrapped in protective materials) and handled with gloves to avoid contamination, ensuring optimal performance during deposition.

Deposition rate depends on factors such as target material and composition, power density, working gas pressure, substrate distance, and the configuration of the sputtering system (e.g., magnetron design).

 
Shopping Cart
Scroll to Top